Input data
- HEB 240 (HE 240 B) column in S355, fy = 355 N/mm² (tf = 17 mm ≤ 40 mm), E = 210 000 N/mm², G = 80 770 N/mm².
- Storey height L = 4.00 m, braced frame, intermediate storey, each storey a separate fire compartment.
- Design effects in fire: Nfi,Ed = 800 kN, My,fi,Ed = 40 kNm, constant over the column height (ψ = 1), Vz,fi,Ed = 20 kN, no moment about the minor axis; γM,fi = 1.0.
- Four-sided exposure, ISO 834 standard curve, required class R 90.
| Quantity | Value |
|---|---|
| h × b × tw × tf × r | 240 × 240 × 10 × 17 × 21 mm |
| A | 106.0 cm² |
| Iy / Iz | 11 260 / 3 923 cm⁴ |
| Wpl,y | 1 053 cm³ |
| It / Iw | 102.7 cm⁴ / 486 900 cm⁶ |
| Am/V (contour, 4 sides) | 130.6 m−1 |
| [Am/V]b (box, 4 sides) | 90.6 m−1 |
1. Cross-section class
- Flange: c = (240 − 10 − 2·21) / 2 = 94 mm; c/tf = 5.53 ≤ 9ε = 6.22, so Class 1.
- Web: c = 240 − 2·17 − 2·21 = 164 mm. The axial force puts the whole web in compression (α = 1), so the Class 1 limit is 396ε / (13α − 1) = 33ε = 22.8; c/tw = 16.4, so Class 1.
The section is Class 1, so Wpl,y is used. Details in the guide on cross-section classes in fire.
2. Slenderness about both axes
Braced frame, intermediate storey, a fire compartment on each storey: ℓfi = 0.5 · L = 2.00 m about both axes (clause 4.2.3.2(4)).
For lateral-torsional buckling the length is the distance between lateral restraints (the floors), LLT = L = 4.00 m, with k = kw = 1.0; the reduction in clause 4.2.3.2(4) applies only to flexural buckling. The moment is uniform, so C1 = 1.00, and the formula in the guide on beams gives:
3. The interaction equations
Clause 4.2.3.5 requires two checks, each at the steel temperature θ. With no moment about the minor axis, the Mz,fi,Ed term drops out:
The moment diagram enters through the equivalent uniform moment factor: for ψ = 1, βM,y = βM,LT = 1.8 − 0.7 · ψ = 1.10. The interaction factors are:
With ky,θ taken out as a common factor, each equation becomes μ0 ≤ ky,θ, where μ0 is the sum of the terms computed with fy at 20 °C. For a temperature θ, compute the slenderness λ̄θ = λ̄ · √(ky,θ / kE,θ), the factors χfi and k, then μ0 and, from eq. (4.22), a new temperature. Repeat until the temperature stops changing.
4. Critical temperature from eq. (4.21a)
At 20 °C: μy = (2 · 1.10 − 5) · 0.254 + 0.44 · 1.10 + 0.29 = 0.063, ky = 0.985 and μ0 = 800 / (0.790 · 3 763) + 0.985 · 40 / 373.81 = 0.269 + 0.105 = 0.375.
| θ (°C) | ky,θ / kE,θ | λ̄y,θ | χy,fi | λ̄z,θ | χz,fi | ky | μ0 | New θ (°C) |
|---|---|---|---|---|---|---|---|---|
| 20.0 | 1.000 | 0.254 | 0.875 | 0.430 | 0.790 | 0.985 | 0.375 | 629.9 |
| 629.9 | 1.555 | 0.317 | 0.845 | 0.536 | 0.735 | 1.071 | 0.404 | 618.4 |
| 618.4 | 1.538 | 0.315 | 0.846 | 0.534 | 0.737 | 1.064 | 0.402 | 618.9 |
| 618.9 | 1.539 | 0.315 | 0.846 | 0.534 | 0.737 | 1.064 | 0.402 | 618.9 |
The minor axis governs, through χmin,fi = χz,fi: eq. (4.21a) gives θa,cr = 618.9 °C. The values of ky,θ and kE,θ are interpolated from Table 3.1.
5. Critical temperature from eq. (4.21b), with lateral-torsional buckling
At 20 °C: μLT = 0.15 · 0.430 · 1.10 − 0.15 = −0.079. The negative value gives kLT above 1, so kLT = 1.000 is used (and at every temperature in the table), and μ0 = 800 / (0.790 · 3 763) + 1.000 · 40 / (0.671 · 373.81) = 0.269 + 0.160 = 0.429.
| θ (°C) | ky,θ / kE,θ | λ̄LT,θ | χLT,fi | λ̄z,θ | χz,fi | kLT | μ0 | New θ (°C) |
|---|---|---|---|---|---|---|---|---|
| 20.0 | 1.000 | 0.659 | 0.671 | 0.430 | 0.790 | 1.000 | 0.429 | 609.0 |
| 609.0 | 1.526 | 0.814 | 0.587 | 0.532 | 0.738 | 1.000 | 0.470 | 594.4 |
| 594.4 | 1.494 | 0.805 | 0.591 | 0.526 | 0.741 | 1.000 | 0.468 | 595.3 |
| 595.3 | 1.497 | 0.806 | 0.591 | 0.526 | 0.741 | 1.000 | 0.468 | 595.2 |
Lateral-torsional buckling governs: θa,cr = 595.2 °C, below the 618.9 °C from eq. (4.21a).
- Shear: Av = 33.24 cm², Vfi,0,Rd = Av · fy / (√3 · γM,fi) = 681.3 kN, μ0 = 20 / 681.3 = 0.029. The critical temperature for shear is above 1000 °C, so shear does not govern.
- Cross-section resistance at 595.2 °C under N, My and Vz (EN 1993-1-1, 6.2.9, with the resistances reduced for fire): the shear force is below half the shear resistance, and the plastic moment reduced by the axial force, MN,y,fi,θ,Rd = 107.9 kNm, exceeds the 40 kNm. The check passes, so the critical temperature stays at 595.2 °C.
6. Time without protection
Integrating eq. (4.25) under the ISO 834 curve, the unprotected steel reaches 595.2 °C after 18.1 minutes. The unprotected column achieves only R 15, so it needs protection for R 90.
7. Protection thickness
Gypsum board protection as a box (λp = 0.20 W/mK, ρp = 800 kg/m³, cp = 1700 J/kgK), Ap/V = 90.6 m−1. With eq. (4.27), the minimum thickness that keeps the steel below 595.2 °C:
| Class | R 30 | R 60 | R 90 | R 120 |
|---|---|---|---|---|
| Required dp | 4.5 mm | 10.5 mm | 16.5 mm | 22.5 mm |
R 90 needs 16.5 mm, provided the properties declared by the manufacturer are at least as good as the values used here. A comparison with other materials is in the guide on boards and sprays.
What affects the result
The same column, with one change to the input data above:
| Change | Mcr | θ from (4.21a) | θ from (4.21b) | dp for R 90 |
|---|---|---|---|---|
| The example above | 861.4 kNm | 618.9 °C | 595.2 °C | 16.5 mm |
| Moment at one end only (ψ = 0; βM = 1.80; C1 = 1.879) | 1 618.6 kNm | 639.9 °C | 605.1 °C | 16.0 mm |
| Equal end moments of opposite sign (ψ = −1; βM = 2.50; C1 = 2.752) | 2 370.7 kNm | 646.0 °C | 610.5 °C | 16.0 mm |
| Double the moment, My,fi,Ed = 80 kNm | 861.4 kNm | 582.1 °C | 544.9 °C | 19.0 mm |
| Higher axial force, Nfi,Ed = 1200 kN | 861.4 kNm | 572.4 °C | 554.1 °C | 18.5 mm |
| Top storey, ℓfi = 0.7 · L = 2.80 m about both axes | 861.4 kNm | 594.1 °C | 580.3 °C | 17.0 mm |
- The moment diagram matters little here: from uniform moment to ψ = −1, Mcr grows almost threefold, but the critical temperature rises by only 15 °C and the board gets 0.5 mm thinner. The axial force makes up most of μ0 (0.269 of 0.429 at 20 °C).
- Doubling the moment lowers the critical temperature by 50 °C, and a 50% higher axial force lowers it by 41 °C.
- On the top storey, ℓfi = 0.7 · L increases the slenderness about both axes, and the protection grows to 17 mm. Lateral-torsional buckling, eq. (4.21b), governs in every case.
Informative material summarising the provisions of EN 1993-1-2. It does not replace the text of the standard, the National Annex or verification by a qualified engineer.